- 11 September 2010
- 4,222
Πέρυσι είχε πάρει το μάτι μου το site της JLSounds μετά από ψάξιμο για USB over I2S converters με πολύ καλά χαρακτηριστικά:
Features of I2SoverUSB
- XMOS 500 MIPS processor
- Sampling frequencies: 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz,
352.8kHz and 384kHz
- 16-, 24- and 32-bit resolution
- DSD Audio over PCM frames. DSD64 (2.8224MHz and 3.0720MHz) and DSD128 (5.6448MHz and 6.1440MHz) by method DoP with 0x05/0xFA
markers
- Directly supports PCM1704, PCM63, PCM61, PCM58, PCM56, AD1862,
AD1865, AD1861, AD1860, AD1851 and other compatible with listed DACs
- Galvanic isolation (outputs, two oscillators and reclock are after the isolator)
- Two low jitter oscillators 45.158MHz and 49.152MHz
- Input for external master clock
- LP5900 ultra low noise linear power regulator
- No switch mode power supplies in the PCB board
- Output for DAC configuration in DSD mode
- I2S, right-justified data or left-justified data (external pin configuration) in 32-bit (channel frame)
- SPDIF output (through DA101C/DA102C transformer) – 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz (16-24 bits)
- I2S, LJ, RJ and S/PDIF outputs work simultaneously up to 192kHz
- Automatic detection of data type (PCM or DSD)
- Master clock outputs: 45.1584/49.1520MHz and 22.5792/24.5760MHz (I2S 22.5792/24.5760MHz are reclocked by edge from 45.1584/49.1520MHz)
- Three different ways to power the board, possible configurations:
- Power by USB bus
- The USB part is powered by USB bus, but the generators and the reclock are fed by a separate external power supply
- Both the USB part and the generators with the reclock are fed by two different external power supplies.
- Dimensions: (LxWxH): 64.0 x 42.3 x 13.9 mm
Drivers:
- No drivers needed for Linux with UAC2 compliant kernel
- No drivers needed for MAC OS version 10.6.4 and above
- ASIO/KS/WASAPI/Direct Sound drivers are necessary for Windows XP to 8 (32 and 64 bit).
και είδα ότι έχουν και dac AK4396
[h=2]Features of AK4396 board[/h]- AK4396 can playback DSD and PCM audio data, as Fs from 44.1 kHz to
192kHz and DSD64 according to its’ datasheet; Proprietary solution for
352.8 kHz, 384 kHz and DSD128
- Configuration from PCM to DSD data format and back, is done by PIC1823
microcontroller, which 0.5sec after his work is done, is putted on sleep mode
not to insert disturbances
- Indicates input sampling rates of PCM and DSD
- AK4396 accepts 16-, 20-, and 24-bit PCM audio data
- Button for selecting digital filter setting
- Reconstruction filter is made of MELF Vishay resistors and polyester
capacitors
- This board is made especially for I2SoverUSB board, but of course one can use it separately
- Dimensions: (LxWxH): 51.0 x 42.3 x 14.0 mm
αποφάσισα να τα δοκιμάσω και τα παράγγειλα μαζί με τις δικές του τροφοδοσίες για να δω τι γίνεται και αν αξίζει τον κόπο... σκέφτηκα στην χειρότερη των περιπτώσεων να μου μείνει ο USB to I2S converter αν τα άλλα είναι μάπα...
Όμως με περίμενε μια ευχάριστη έκπληξη...
Αφού τα μοντάρισα στο χιλιοτρυπημένο μου δοκιμαστικό κουτί...
Ο ήχος ήταν πολύ φυσικός τόσο που δεν το περίμενα... εκπληκτική στερεοφωνική εικόνα, εξαιρετική λεπτομέρεια, και πολύ σαφή τοποθέτηση των οργάνων στο χώρο...και όλα αυτά χωρίς να κουράζει πουθενά... (ένα χαρακτηριστικό των φτηνών DAC, είναι αυτός ο εντυπωσιακός αλλά πολύ κουραστικός ήχος...).
Αποφάσισα να φτιάξω καλές τροφοδοσίες για να δω που μπορεί να το φτάσω...
Enter Salas Shunts...
Εχθές είχα δουλειά απ ότι βλέπετε...
Και ιδού το αποτέλεσμα μετά από ένα γεμάτο εξαωράκι, συναρμολόγηση και έλεγχος Salas, τρύπημα και διευθέτηση κουτιού, τελικοί έλεγχοι, και...voila:
Features of I2SoverUSB
- XMOS 500 MIPS processor
- Sampling frequencies: 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz,
352.8kHz and 384kHz
- 16-, 24- and 32-bit resolution
- DSD Audio over PCM frames. DSD64 (2.8224MHz and 3.0720MHz) and DSD128 (5.6448MHz and 6.1440MHz) by method DoP with 0x05/0xFA
markers
- Directly supports PCM1704, PCM63, PCM61, PCM58, PCM56, AD1862,
AD1865, AD1861, AD1860, AD1851 and other compatible with listed DACs
- Galvanic isolation (outputs, two oscillators and reclock are after the isolator)
- Two low jitter oscillators 45.158MHz and 49.152MHz
- Input for external master clock
- LP5900 ultra low noise linear power regulator
- No switch mode power supplies in the PCB board
- Output for DAC configuration in DSD mode
- I2S, right-justified data or left-justified data (external pin configuration) in 32-bit (channel frame)
- SPDIF output (through DA101C/DA102C transformer) – 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz (16-24 bits)
- I2S, LJ, RJ and S/PDIF outputs work simultaneously up to 192kHz
- Automatic detection of data type (PCM or DSD)
- Master clock outputs: 45.1584/49.1520MHz and 22.5792/24.5760MHz (I2S 22.5792/24.5760MHz are reclocked by edge from 45.1584/49.1520MHz)
- Three different ways to power the board, possible configurations:
- Power by USB bus
- The USB part is powered by USB bus, but the generators and the reclock are fed by a separate external power supply
- Both the USB part and the generators with the reclock are fed by two different external power supplies.
- Dimensions: (LxWxH): 64.0 x 42.3 x 13.9 mm
Drivers:
- No drivers needed for Linux with UAC2 compliant kernel
- No drivers needed for MAC OS version 10.6.4 and above
- ASIO/KS/WASAPI/Direct Sound drivers are necessary for Windows XP to 8 (32 and 64 bit).
και είδα ότι έχουν και dac AK4396
[h=2]Features of AK4396 board[/h]- AK4396 can playback DSD and PCM audio data, as Fs from 44.1 kHz to
192kHz and DSD64 according to its’ datasheet; Proprietary solution for
352.8 kHz, 384 kHz and DSD128
- Configuration from PCM to DSD data format and back, is done by PIC1823
microcontroller, which 0.5sec after his work is done, is putted on sleep mode
not to insert disturbances
- Indicates input sampling rates of PCM and DSD
- AK4396 accepts 16-, 20-, and 24-bit PCM audio data
- Button for selecting digital filter setting
- Reconstruction filter is made of MELF Vishay resistors and polyester
capacitors
- This board is made especially for I2SoverUSB board, but of course one can use it separately
- Dimensions: (LxWxH): 51.0 x 42.3 x 14.0 mm
αποφάσισα να τα δοκιμάσω και τα παράγγειλα μαζί με τις δικές του τροφοδοσίες για να δω τι γίνεται και αν αξίζει τον κόπο... σκέφτηκα στην χειρότερη των περιπτώσεων να μου μείνει ο USB to I2S converter αν τα άλλα είναι μάπα...
Όμως με περίμενε μια ευχάριστη έκπληξη...
Αφού τα μοντάρισα στο χιλιοτρυπημένο μου δοκιμαστικό κουτί...
Ο ήχος ήταν πολύ φυσικός τόσο που δεν το περίμενα... εκπληκτική στερεοφωνική εικόνα, εξαιρετική λεπτομέρεια, και πολύ σαφή τοποθέτηση των οργάνων στο χώρο...και όλα αυτά χωρίς να κουράζει πουθενά... (ένα χαρακτηριστικό των φτηνών DAC, είναι αυτός ο εντυπωσιακός αλλά πολύ κουραστικός ήχος...).
Αποφάσισα να φτιάξω καλές τροφοδοσίες για να δω που μπορεί να το φτάσω...
Enter Salas Shunts...
Εχθές είχα δουλειά απ ότι βλέπετε...
Και ιδού το αποτέλεσμα μετά από ένα γεμάτο εξαωράκι, συναρμολόγηση και έλεγχος Salas, τρύπημα και διευθέτηση κουτιού, τελικοί έλεγχοι, και...voila: