Σύμφωνα με
αυτό το τεστ -πηγαίνετε στις μετρήσεις στο τέλος- το df του 110 είναι μόλις 16, "όπως περίπου και στους Naim".
Δεν φαίνεται αυτό να έχει σχέση με τα ρεύματα, μια και -στον ίδιο πίνακα- βλέπουμε ότι ο 110 μετράει 78 και 144W για 8 και 4Ω αντίστοιχα.
Φαίνεται όμως να έχει σχέση με την
απουσία ανάδρασης. Σύμφωνα με
αυτό το άρθρο:
"Very high DF suggests an amplifier uses a lot of feedback".
Η πολύ ενδιαφέρουσα κουβέντα που γίνεται
εδώ έχει πολλά και σημαντικά, ακόμα έχει links για περαιτέρω μελέτη κ.λπ.
Καταρχήν:
Essentially [df] relates to amplifier output impedance.
The lower the output impedance the higher the damping factor.
Πιο κάτω:
A high damping factor is generally considered to be desirable, but it's not likely to be worth paying money to get stupidly high values. Passive crossovers (particularly inductors, which includes speaker cables) will generally crap all over any amplifier's DF.
(Δείτε, σε σχέση με το τελευταίο,
τούτο το αρθράκι σύμφωνα με το οποίο, από έναν ενισχυτή με εμπέδηση εξόδου=0.0025Ω, δηλ. df=3200 (!!!)
το γούφερ θα "δει" df μόλις 10,6!!!
Συμπέρασμα:
Many audio engineers are of the opinion that an amplifier damping factor of 10 or greater is adequate. Those sky high damping factors seen on the spec sheets of some amps are frequently just inventions of the marketing department and are irrelevant to actual system performance.)
Και το σημαντικότερο, που σχετίζεται με ό,τι συζητάμε εδώ και αλλού περί
συνέργειας:
It's easy to show in a loudspeaker designing program that if you take a passive loudspeaker that is designed, let's say, with an amp with 1 Ohms of output impedance, and substitutes it with one with a lower and "better" output impedance, the transient response after the passive filter is actually worse! So a lower output impedance isn't allways better.
The perfect amp, when it comes to output impedance, is one that has the same output impedance (over the frequency range) as the one used when designing the loudspeaker that are to be driven.
Και από το άρθρο του Hi Fi World:
Loudspeakers are damped mechanically by the air load, magnetically by the motor and electrically by the amplifier.
A loudspeaker can be acoustically over damped, in which case no extra electrical damping from the amplifier is necessary. [...] so a Single Ended amplifier with no feedback and little bass control needs to be matched with a well damped loudspeaker.
Μετά από αυτή τη σεντονούκλα με τα τσαλαβουτήματα ενός άσχετου (εμού δηλαδή) από δω κι από κει, μπορεί ίσως ο Νίκος να μας διαφωτίσει σχετικά με το Tower και την επιρροή του (απ' ό,τι καταλαβαίνω υπερεκτιμημένου) damping factor στο σχέδιό του.