ΑΦΙΞΗ ΣΤΗΝ ΕΛΛΑΔΑ ΤΟΥ PHONO PREAMPLIFIER ΤΗΣ AUDIO VALVE

audiophile62

AVClub Enthusiast
9 February 2007
1,292
Αθηνα-Γλυφαδα
Διατιθεται ηδη απο την εδω αντιπροσωπεια το λαμπατο Phono Stage της Γερμανικης Audio Valve με την ονομασια Sunilda. Προκειται για ενα απο τα καλυτερα phono stages με Διθυραμβικες κριτικες στον Διεθνη Ειδικο Τυπο, το οποιο παρεχει τη δυνατοτητα μεσω ριθμιστικων στην προσοψη του , να το προσαρμοζει ο χρηστης σε ΟΠΟΙΑΔΗΠΟΤΕ κεφαλη , κατα τη διαρκεια της λειτουργειας του ( σε πραγματικο χρονο ) καθως επισης και τη συνδεση δυο κεφαλων/βραχιονων παραλληλα ( διπλο Phono Stage ). Aξιχει να αναφερθει οτι εχει ΕΞΩΤΕΡΙΚΟ τροφοδοτικο και το βαρος του ειναι περι τα 20KG !!


AudioValve`s RIAA MC and MM phono amp
[FONT=Comic Sans MS,Bold]:: SUNILDA ::[/FONT]
NEW !!!
[ review hifinews 2005: ]




neueplatine2.jpg

A view of the compact and absolute wireless electronic - riaa modul from SUNILDA. There is no hum, bee or any noise - only music. The design on a double side pc board is constructed in double mono technology, use best and selected components and guarantee high stable and highend venyl re - productions.



[FONT=Comic Sans MS,Bold]Product Description[/FONT]

Sundila is a three stage phono-preamplifier, based on 6922 (ECC88) and12AX7 (ECC83) frame grid tubes, suitable for MM- and MC-cartridges. Independently for the two phono inputs, impedance and capacitive load can be set separately and 'on-the -fly' while listening. Thus the user can easily configure the unit to match the features of the cartridge by selecting the optimal input resistance and capacitance for each input separately!

fertig.jpg

Switches are found for: MM/MC mode for each input; input 1 or 2; selectors are used to select different R and C loads.

fertig2.jpg

two selector knops for each input capacitive and resistor load

In MM mode the gain will be 20 dB lower than MC and at a fixed input-impedance of 47 K.
In MC mode the preamp will have higher gain and switchable input resistors and condensers. The RIAA de-emphasis is passive and split between the first and second stage. Dividing the RIAA network over two amplification stages lowers the insertion losses of the passive network dramatically .Furthermore, the design holds a total absence of feedback, thus increasing the overall dynamics.
hinten.jpg

rearside panel from SUNILDA

Power supplies are solid state regulated. This is the best way to obtain a low noise and supply line with a very low impedance that will increase the performance in the lower frequency range. The power transformer is housed in a separate aluminum case.

netz.jpg

separate power supply case

Sunilda comes in an lasercut, 4 mm thick steel, chassis in black or silver finish and has a case similar to the Eklipse lineamplifier.

front.gif

function selectors at the SUNILDA frontpane

l
Technical Specifications:MM mode gain: [FONT=Comic Sans MS,Bold]40dB - 1Khz[/FONT]
MC mode gain: [FONT=Comic Sans MS,Bold]60 dB - 1Khz[/FONT]
MM / MC mode input impedance:
resistors:[FONT=Comic Sans MS,Bold]47 R, 100 R, 220 R,[/FONT][FONT=Comic Sans MS,Bold]470 R, 1 K, 47 K[/FONT]
capacitors:0 p, 100 p, 220 p, 470p
Frequency Response: [FONT=Comic Sans MS,Bold]20Hz to 65 KHz +/- 3 dB[/FONT]
Subsonic filter roll-off: [FONT=Comic Sans MS,Bold]20 Hz[/FONT]
Max output amplitude: [FONT=Comic Sans MS,Bold]14V pk[/FONT]
Max input amplitude: [FONT=Comic Sans MS,Bold]200 mV[/FONT]
RIAA accuracy: [FONT=Comic Sans MS,Bold]+/- 0,25dB[/FONT]
Distortion: [FONT=Comic Sans MS,Bold]0,24 % (1Khz - 10Vpk out)[/FONT]
Noise: [FONT=Comic Sans MS,Bold]76 dB below signal (MC mode)[/FONT]
Circuit type: [FONT=Comic Sans MS,Bold]3 stages single ended, buffered ouputs[/FONT]
RIAA network [FONT=Comic Sans MS,Bold]passive - split between 1st and 2nd stage[/FONT]
Resistors: [FONT=Comic Sans MS,Bold]1 % metal film[/FONT]
Capacitors: [FONT=Comic Sans MS,Bold]MKP - styroflex - fast electrolytic[/FONT]
Tubes: [FONT=Comic Sans MS,Bold]2 x 6922,[/FONT]2 x 12ax7
more mode functions: Stand - by and mute
Power supplies: [FONT=Comic Sans MS,Bold]Solid state regulated[/FONT]
Power transformer: [FONT=Comic Sans MS,Bold]outside in a separate case[/FONT]
Power requirements: [FONT=Comic Sans MS,Bold]115/230 - 245 Ac - 50/60Hz[/FONT][FONT=Comic Sans MS,Bold]
[/FONT]
Powerconsumption: Watts: 60 VA
Dimensions:cm, W x H x D :42 * 32 * 14 (same as Eklipse)
Weight:Kg: 20 kg