βοηθεια για επιλογη home cinema

maik36

New member
8 February 2007
21
εχω εναν ενισχυτη LUXMAN LV-113 και ηχεια τα B&W DM 640 τα οποια τα ειχα αγορασει πριν 15 χρονια και ειμαι πολυ ευχαριστημενος
απο την αποδοση και των δυο.το θεμα ειναι οτι θελω να κανω home cinema και δεν θελω να τα αποχωριστω ουτε βεβαια
να πληρωσω μια περιουσια.τι επιλογες εχω μεχρι 400-450 ευρω και ποια μηχανηματα προτεινετε ?? (χωρις κεντρικο και περιφερειακα ηχεια,αυτα θα τα παρω τσαμπα απο φιλο :) )
 
Last edited:
Πολυκάναλο ενισχυτή σ' αυτήν την κατηγορία τιμής που να οδηγήσει ηχεία 4Ω σαν τα B&W DM640 δεν θα βρεις.

Κοίταξε καλύτερα για ΟΝΚΥΟ TX-SR607

http://www.kotsovolos.gr/site/product.jsp?catid=10024561&cmicc=skroutz

ή καλύτερα τον TX-SR707

Από το FAQ της Onkyo

Can my ONKYO amplifier or receiver drive 4 ohm speakers?
Our amplifiers and receivers incorporate high quality materials and technical concepts to provide the best sound quality and a safe listening environment in which to enjoy music and movies for many years. But, due to CE configuration regulations, we can only guarantee safe use with minimum 6-ohm speakers.
However, many speakers operate at 4 ohms, and some even drop below 4 ohms at certain frequencies. In certain circumstances, both speakers and amplifier could be seriously damaged or even destroyed. For example:

if the 4 ohm speaker's resistance drops below 4 ohms at certain frequencies;
if you are listening to the music at a very loud volume;
if you are playing extremely dynamic music (for example, CDs with high-level equalization, or recordings like "Tschaikowsky 1812" or "Charly Antolini-knock out" or other highly dynamic material).
This combination of factors can be very dangerous and should be avoided. Please contact your dealer or distributor to find out about the impedance response of your speakers (over their entire frequency range!).
Unfortunately, it is our experience that some speakers do have difficulties in their impedance response.
Also please note that using 50 to 60% of the maximum volume indication set with the volume will give you full clean power output of the power stage. Turning the volume up further will not increase the volume but will increase distortion which could endanger your amplifier and your speakers.
 
Και αυτά τα λέει η ONKYO παρόλο που στα manual των ενισχυτών της γράφει σύνδεση με ηχεία 4 - 16 Ω.
Οι υπόλοιποι (Pioneer, Denon, Yamaha) το αναγράφουν χαρακτηριστικά:
Σύνδεση μόνο με ηχεία nominal impedance 6 - 16 Ω.....
 
Κώστα αυτοί θα μας τρελάνουν όλους.
Αντιγράφω πάλι από το FAQ της Onkyo.

Can I use the receiver TX-SR 506/507/576/577/605/606/607/705/706/707/805/806/875/876 and TX-NR 807/905/906 with 4 ohm speakers in bi–amping mode?

Yes you have to select at hardware setup of the receiver the speaker impedance to 4 ohm.
 
Last edited:
τα DM 640 θεωρουσα οτι θα τα συνδεσω στον LUXMAN ο οποιος συνδεεται με pre out σε οποιον επιλεξω και τα περιφερικα μονο θα παρουν σημα απο τον καινουργιο γι'αυτο και δεν θεωρησα οτι ειναι απαραιτητο να ανεβω τοσο πολυ στο buget.. δεν ξερω υπαρχει κατι λαθος στην λογικη μου?
 
Κώστα αυτοί θα μας τρελάνουν όλους.
Αντιγράφω πάλι από το FAQ της Onkyo.

Can I use the receiver TX-SR 506/507/576/577/605/606/607/705/706/707/805/806/875/876 and TX-NR 807/905/906 with 4 ohm speakers in bi–amping mode?

Yes you have to select at hardware setup of the receiver the speaker impedance to 4 ohm.


Το ξέρω Γιάννη, έχω ψάξει τα manual της ΟΝΚΥΟ και είναι η μόνη εταιρεία που λέει ότι μπορείς να συνδέσεις ηχεία 4Ω στους ενισχυτές της.

Ενδεικτικά αναφέρω την Pioneer, που λέει ότι ηχεία 4Ω μπορείς να συνδέσεις μόνο στον LX90 Susano που κάνει σχεδόν 5.000 ευρώ.....