Nέα προϊόντα Hi End εταιρειών.

Παιδια απο'τι βλεπω στο site της xtz υπαρχει ο καινουριος τελικος της, ο
Class AP-100 με λειτουργια σε ταξη Α και ΑΒ. Ιδου και μια φωτο
 

Attachments

  • xtzclassap100.jpg
    xtzclassap100.jpg
    24.1 KB · Views: 25
Απάντηση: Re: Nέα προϊόντα Hi End εταιρειών.

Παιδια απο'τι βλεπω στο site της xtz υπαρχει ο καινουριος τελικος της, ο
Class AP-100 με λειτουργια σε ταξη Α και ΑΒ. Ιδου και μια φωτο

ΑΒ είναι.
Αυτό σημαίνει,ότι όλες οι αντίστοιχες κατασκευές,αποδίδουν κάποια λίγα wrms σε τάξη Α.
 
Re: Απάντηση: Re: Nέα προϊόντα Hi End εταιρειών.

ΑΒ είναι.
Αυτό σημαίνει,ότι όλες οι αντίστοιχες κατασκευές,αποδίδουν κάποια λίγα wrms σε τάξη Α.

Το συγκεκριμένο μοντέλο δεν το γνωρίζω, αυτό όμως που έχω (classe ca-2200) δίνει το 1/3 της ισχύος σε τάξη Α (περίπου τα 65 watt)
 
Απάντηση: Re: Απάντηση: Re: Nέα προϊόντα Hi End εταιρειών.

Το συγκεκριμένο μοντέλο δεν το γνωρίζω, αυτό όμως που έχω (classe ca-2200) δίνει το 1/3 της ισχύος σε τάξη Α (περίπου τα 65 watt)

Χλωμό...Θα πρέπει νάναι πάνω απο...100 κιλά και με τεράστιες ψύχτρες...
 
Re: Απάντηση: Re: Απάντηση: Re: Nέα προϊόντα Hi End εταιρειών.

Χλωμό...Θα πρέπει νάναι πάνω απο...100 κιλά και με τεράστιες ψύχτρες...

Δεν γνωρίζω πολλά (για τάξεις, ηλεκτρικά γενικά), η Classe πάντως λέει:

"
Class A
For Classé amplifiers, output stage DC bias is set to idle at a relatively low level to minimize heat. As the output increases under load, the bias increases, remaining at about 1/3 of the total output power. So for example, a Classé amplifier delivering 100W into an 8 load will be operating at about 30W Class A, eliminating any effect of switching distortion normally associated with a Class A/B design."
 

Attachments

  • tadd6006.jpg
    tadd6006.jpg
    58.7 KB · Views: 20
  • tadd6005.jpg
    tadd6005.jpg
    59.5 KB · Views: 27
  • tadd6004.jpg
    tadd6004.jpg
    63.5 KB · Views: 17
  • tadd6003.jpg
    tadd6003.jpg
    43.6 KB · Views: 16
  • tadd6002.jpg
    tadd6002.jpg
    50 KB · Views: 24
  • tadd6001.jpg
    tadd6001.jpg
    75.1 KB · Views: 25
  • TAD_system_big.jpg
    TAD_system_big.jpg
    81.7 KB · Views: 34
Mark Levinson

Power amplifier
No.531H
No.532H

Τους ειδαμε στο show του ΤOKIO/TOKYO σε στατικη επιδειξη.
Η Mark Levinson ανακοινωσε και επισημα τους δυο νεους ενισχυτες.

300w στα 8Ω, ο 531Η mono και ο 532H dual-mono.
S / N Ratio: 85dB or more (1W standards)
input: XLR × 1, RCA × 1
Dimensions: 451W × 194H × 504Dmm Weight: 23.8kg

(532H).....input: XLR × 1/ch, RCA × 1/ch/Weight: 33.6 kg

From input to output, amplifier circuit configuration adopted a fully balanced symmetrical layout. This common-mode noise, which will reduce both the differential mode noise. No.531H1、「No.532H」2The monolithic amplifier module includes channel independent power transformer, "No.531H" to one group, "No.532H" to be equipped with two units.
Borutejigeinsuteji up from the input signal path to minimize the circuit configuration uses a simple and compact. No high-speed signal propagation and transmission loss was less rapid signal processing allows the phase rotation and parasitic capacitance.

In order to supply power directly to the audio circuit balanced configuration, with a rectifier power supply circuit capacity on the same board. The power circuitry on the main board directly to a large toroidal power transformer for each channel independently, which reduces power loss and eliminates the increase in impedance of the circuit to supply power to the power stage in the shortest distance.

In addition, the rectifier and capacitors ensure sufficient capacity for the large number of capacitors connected in parallel and agile small capacity, low loss of the strict power / power supply design speed adopted. Leveraging this simple audio circuit, that allow you to further speed gain.

In addition, across the output circuit using a large heat sink, a physical separation between the parts of the circuit and power supply input Borutejigeinsuteji. Is to minimize interference.

10Hz20kHzS/N (1W 85dB Frequency response is 10Hz to 20kHz in, S / N Ratio (1W standards) is more than 85dB. 「No.531H」RCAXLR1「No.532H」RCAXLR1/chInput is "No.531H" to RCA (unbalanced) and XLR (balanced) each time one strains, "No.532H" RCA (unbalanced) and XLR (balanced) each one strain / ch are equipped .60kΩ30kΩ。 Balanced input impedance is 60kΩ, unbalanced 30kΩ.




Kυκλοφορουν στις αρχες Απριλιου.

http://translate.googleusercontent....nslate.google.co.jp&usg=ALkJrhgHfbRsNEPrtDs7A

...
 

Attachments

  • 526.jpg
    526.jpg
    111.7 KB · Views: 19
  • 519.jpg
    519.jpg
    114.3 KB · Views: 14
  • 522.jpg
    522.jpg
    132.2 KB · Views: 14
  • 518.jpg
    518.jpg
    129.1 KB · Views: 13
  • 517.jpg
    517.jpg
    152.1 KB · Views: 15
  • 516.jpg
    516.jpg
    111.2 KB · Views: 12
  • 513-3.jpg
    513-3.jpg
    96 KB · Views: 20
  • 513.jpg
    513.jpg
    85.7 KB · Views: 15
  • 512.jpg
    512.jpg
    86.6 KB · Views: 19
  • harman-mark531_big.jpg
    harman-mark531_big.jpg
    46.6 KB · Views: 33